The cable penetrators have wrench flats that making tightening relatively easy, but when you pack a bunch of them together it gets more difficult. That’s particularly true with the 14-hole end-cap used on the BlueROV2. This specially designed wrench makes it easy to tighten penetrators in tight spaces.
The wrench is make a chrome-plated steel and includes a lever bar designed to apply just the right amount of torque to tighten the penetrator. The 16mm inside width works with all of our penetrators. This tool is a great addition to your field toolbox!
Note: We recommend tightening the penetrators with your fingers and then use this wrench to tighten just slightly past that point. When done, you should not be able to remove the penetrators by hand.
Contents
Technical Details
Learn
- 1 x Penetrator Wrench
- 1 x Lever Bar
Specifications
Parameter | M06 | M10 | M14 |
---|---|---|---|
Part Number | WL-M06-BULKHEAD-WRENCH | WL-M10-BULKHEAD-WRENCH | WL-M14-BULKHEAD-WRENCH |
Material | Chrome-plated steel hardened to HRC 32-36 | ||
Square Drive Size | 1/4 in (6.3 mm) | 3/8 in (9.5 mm) | |
Wrench Flats | 12 mm | 16 mm | 20 mm |
Penetrator Compatibility | All M06 size bulkheads | All M10 size bulkheads | All M14 size bulkheads |
WLP Tool Information
Seal Size | Bulkhead Size | Bulkhead Wrench |
Bulkhead/ Nut Flat Size |
Bulkhead Installation Torque |
---|---|---|---|---|
4.5 | M06 | WL-M06-BULKHEAD-WRENCH | 12 mm | 1 N⋅m |
4.5 | M10 | WL-M10-BULKHEAD-WRENCH | 16 mm | 3.5 N⋅m |
5.5, 6.5, 7.5, 8.5 | M10 | WL-M10-BULKHEAD-WRENCH | 16 mm | 3.5 N⋅m |
9.5 | M14 | WL-M14-BULKHEAD-WRENCH | 20 mm | 3.5 N⋅m |
* The WetLink Penetrator Assembly Block is compatible with all WetLink Penetrator sizes |
Seal Size | Bulkhead Size | Plug Wrench | Plug Hex Size | Plug Installation Torque |
---|---|---|---|---|
4.5 | M06 | WLP-11MM-PLUG-WRENCH | 11 mm | 14 N⋅m |
4.5 | M10 | WLP-11MM-PLUG-WRENCH | 11 mm | 14 N⋅m |
5.5, 6.5, 7.5, 8.5 | M10 | WLP-14MM-PLUG-WRENCH | 14 mm | 14 N⋅m |
9.5 | M14 | WLP-18MM-PLUG-WRENCH | 18 mm | 20 N⋅m |
* The WetLink Penetrator Assembly Block is compatible with all WetLink Penetrator sizes |
2D Drawings
WL-M06-BULKHEAD-WRENCH-R1 (.pdf)
WL-M10-BULKHEAD-WRENCH-R1 (.pdf)
WL-M14-BULKHEAD-WRENCH-R1 (.pdf)
3D Models
WL-M06-BULKHEAD-WRENCH-R1 (.zip)
WL-M10-BULKHEAD-WRENCH-R1 (.zip)
WL-M14-BULKHEAD-WRENCH-R1 (.zip)
Quick Start
- Tighten the penetrators to finger tight, then use the Bulkhead Wrench to tighten them an additional ~1/16 of a turn.
- If you can’t loosen them with your fingers, they are tight enough.